Plumbing Services In Riverside, CA

Had to run my main line machine through ground clean out in the warehouse. I

Installed new exterior hose bibbs, replaced laundry room bibbs, and updated angle stops throughout the home. Each fixture was securely fitted and pressure-tested to ensure leak-free operation. This upgrade improves water control and enhances overall plumbing reliability inside and out.

provided Estimate to install new wall cleanout going to the outside. We would have to cut open the cabinet backer to get access to the drain line. Once we have access to the drain line, we will install a cleanout going to the outside. After installing the new cleanout, we will put the piece of cabinet backer back up And seal it with caulking. Bow Tie Plumbing will also Hydro jet the kitchen sink drain line to remove grease and debris.

Estimate to reroute dryer vent. We will eliminate the old dryer vent that goes into the concrete. Install approximately 30 feet of 4 inch single wall galvanized venting starting from the laundry closet going into the attic and exiting on the side of the house. We will strap the 4 inch vent, going up the wall and along the rafters in the attic. Install a dryer vent kit going to the outside each joint will be taped and sealed.

Moen Flo and riser buildup Moen Flo install. Reworked riser to home with new 3/4 ball valve, tee, and hose bib. Added Moen Flo to riser, and reused existing pressure regulator. Smart valve will need a power outlet installed to operate. An electrician will need to install the outlet outside near the smart valve. 1 year warranty on workmanship. Replaced two old half inch gas shutoffs. One for the dryer and one for the water heater. Relit water heater pilot light. 1 year warranty on workmanship. Dryer vent cleaning: Cleaned dryer vent by pulling dryer out from its place and running a vent cleaner. Unable to clear blockage, ran camera to find corroded and collapsed pipe engulfed in dirt. Dryer vent will need to be replaced to fix the problem.

Gas Leak: 3/4 inch gas line in crawlspace leaking, replaced pipe with new 3/4 inch csst pipe. Connected to iron pipe ball valve at meter, secured new pipe in crawlspace with pipe straps and reconnected to iron pipe tee supplying both furnaces. Pressure tested new gas line with air, no leaks. Pressurized line with gas and double checked all joints made, no leaks. 1 year warranty on workmanship.

I installed a new Dervlive kitchen sink faucet with a pull-down sprayer. I also replaced the angle stops for the hot and cold water lines.

estimate provided to install new angle stops in kitchen and pressure regulator

Spud replacement for Kohler toilet

I was called to a leak in a wall. Upon inspection, I found that the customer had made a repair, but there were no leaks present. I moved the copper manifold away from the touching area to prevent electrolysis. The pressure in the system was 85 psi, which is within the normal range. I recommended replacing the pressure regulator to ensure proper pressure management.

I had to remove the cover to access the pump and start filling it up. I tested the floats and made sure there was nothing in the tank. After that, I turned on the mop sink to fill it up and check for leaks. Everything looked good, so I turned off the water and disconnected the hose.

I was called to a commercial property to fix a clogged toilet. Upon inspection, I found that the toilet was clogged with paper towels. I removed the paper towels and restored proper flushing.

I had to run my main line machine through the ground clean out in the warehouse. I pulled back nothing. I then removed the old caulking from the toilet and installed a new wax ring, bolts and reinstalled the customers toilet

I was called to a home to fix a problem with the water pump. I arrived and found that the pumps were not working automatically. I checked the floats and noticed that they were not working properly. I removed the paper towel that was wrapped around the pump and the float and tested the pumps 4 times by filling up water until the float started to work again.

I found a leaking shower valve and replaced the cartridge in the valve.

I received a call about a toilet in the men's restroom that was not flushing properly. I arrived at the scene and found that the toilet was clogged. I used a cable to try to clear the clog, but it was unsuccessful. I then rebuilt the Sloan flush valve, diaphragm, tail piece o-ring, inside cover, and vacuum breaker seal for the toilet. After completing the repairs, the toilet was working properly again.

I was called to a home to repair a toilet that was not flushing properly. I diagnosed the issue as a clog in the toilet and recommended a rebuild to ensure a proper flush and push all the paper down the drain.

I was called to a store to replace the floats in a dual pump septic system. The floats were not working and the system was not pumping. I replaced the floats and ran wires into the alarm casing to fix the issue.

I was called to fix a leak in a women's restroom. I found that the angel stop valve was leaking. I replaced the valve and the leak was fixed.